Sponsors:



Most Popular:

  258 Carter BBD Idle Problem
  42re Transmission
  AMC 20 Axle
  AMC 242 4.0l Engine
  AMC 258 I6 Engine
  AMC 304 V8 Engine
  AX 15 Transmission
  AX 5 Transmission
  Axle Upgrades
  CJ-5
  CJ-7
  Dana 30 Axle
  Dana 44 Axle
  Front Dana 44 Axle Swap
  Jeep CJ Gauge
  Jeep Engine Upgrades
  Jeep Tires
  Jeep Transmission
  Rear Dana 44 Axle Swap
  Transmission Conversion

Borgeson Steering Shaft for Jeep CJs

A stronger alternative to factory replacement parts

by John Nutter


Steering shaft replacement is a common need for CJ owners since all CJs are at least 13 years old by now. Factory replacements parts are still available, but they tend to wear out quickly when used with large tires in off-road conditions. The boot on the factory bell coupler at the lower end of the factory shaft tends to wear out and allow grit into the bell coupler assembly, causing wear to accelerate. The factory upper U-joint is not sealed and does not incorporate any type of bearing.

There is a better answer than replacing your worn steering shaft with OEM replacement parts. Borgeson makes replacement steering shafts for CJs and many other types of vehicles that incorporate much stronger sealed needle bearing type U-joints. Because the U-joints are of the needle bearing design and are are sealed, they will last much longer under hard conditions. Another positive aspect of the needle bearing type U-joints is that they are able to withstand higher torque loads than the factory parts.

Installation

Installation of the Borgeson steering shaft was quick and painless. Including the time to remove the fender for pictures, and working with only hand tools, I was able to install the steering shaft in under 1/2 hour. There is normally no need to remove the fender, I only removed mine to get clearer pictures.

The procedure is very straight forward:

Remove the existing steering shaft: There is a bolt at each end of the shaft that must be completely removed because they ride in a groove on the steering column and steering box. Once the bolts are out, tapping lightly with a hammer will dislodge the old steering shaft. No further disassembly is required.

shaft comparison
The stock shaft is shown on top and the Borgeson shaft is on the bottom. The Borgeson shaft is shown with the slip joint collapsed in this picture. The Borgeson shaft can easily expand enough to fit a 3" body lift.

Install the new steering shaft: Align the set screws with the flats on the steering column and the steering box. Extend the shaft to the proper length and tighten down the set screws and jam nuts.

shaft installed
The set screw on the Borgeson shaft must align with the flat on the steering column. There is a similar flat on the seering box for the other set screw. The shaft was expanded further after the photo to place the set screw in the center of the flat area.

Impressions

An immediate improvement in steering precision was noted because the play from the worn joints on the old shaft was gone. On the road wandering was reduced, and off-road the unit worked perfectly. Steering feel was enhanced by removing the play from the steering shaft.

I tested the steering shaft off-road at the Moab Easter Jeep Safari, and I have put on hundreds of street miles. I could find no flaw with the Borgeson steering shaft.

Borgeson Universal Company, Inc
Dept. ORC
187 Commercial Blvd
Torrington Ct 06790-3098
860-482-8283
FAX 860-496-9320


Last modified Wednesday, 01-Dec-2010 08:17:47 MST


[ Jeep Tech Main Page | Terry's Jeep Page ]

Copyright © 2001, 2000, 1999, 1998 JEEPTECH.COM
All Rights Reserved, All content with exception of private works and
corporate trademarked logos are property of Jeeptech.com




Leave a Comment:
Name:

(Not a Spam Bot)

Comments: